ICub software

This article deals with the installation of YARP and iCub software. Word of advice: always refer to the official iCub documentation first:

• http://www.yarp.it
• http://wiki.icub.org/wiki/Manual#Six._Software.2C_Installing_YARP_and_iCub
• http://wiki.icub.org/wiki/ICub_Software_Installation
• Virtual Machine that contains pre-installed software: https://github.com/robotology/vagrant-icub

Below, we list some unofficial additional notes provided by VisLab members.

See iCub software/Archive for obsolete information.

Dependencies

In Linux, refer to iCub machines configuration#Dependencies.

Environment variables

The following environment variables must be set.

• YARP_ROOT: location of the yarp source code
• YARP_DIR: yarp build directory, usually YARP_ROOT/build
• ICUB_ROOT: location of the icub-main source code
• ICUB_DIR: icub-main build directory, usually ICUB_ROOT/build

In Linux, refer to iCub machines configuration#Environment variables.

YARP

Browsing the yarp repository online

https://github.com/robotology/yarp

Getting the yarp repository in Windows

Inside TortoiseGit, use the file manager to browse to the location where you would like to download the code; right click on an empty region of the window and select "checkout" from the contextual menu; type the above address in the "URL of repository" field. No password or username will be required.

Note: if you use Cygwin, refer to Linux instructions instead.

Installing yarp in Windows

Note: all environment variables should have '/' and NOT '\' (except in the PATH enviroment variable).

Getting the yarp repository in Linux

Run the following command in a console terminal, typically from the $code directory:

git clone https://github.com/robotology/yarp.git

Compiling the yarp repository in Linux

mkdir $YARP_DIR
cd $YARP_DIR
ccmake $YARP_ROOT

In the CMake interface, set the following

CMAKE_BUILD_TYPE Release
CREATE_LIB_MATH ON

then hit c and g in order to generate the project files, to obtain the Makefile.

Having generated your project file, only the actual compilation remains to be done:

make

Don't use sudo make install! Rather, add the location of the binaries to the $PATH environment variable (see below).

Updating the yarp repository in Linux

cd $YARP_ROOT
git pull

Downloading YARP as a single file

Refer to http://www.yarp.it. Pre-compiled binaries are also available.

iCub

Browsing the iCub repository online

icub-main

https://github.com/robotology/icub-main/

iCub Contrib Software

These are small repositories in the Robotology organization page, which contain special components and demos, for example the ball tracking and grasping demo is here: https://github.com/robotology/icub-basic-demos/

Getting the iCub repository in Windows

Inside TortoiseGit, use the file manager to browse to the location where you would like to download the code; right click on an empty region of the window and select "checkout" from the contextual menu; type the repository address in the "URL of repository" entry.

Note: if you use Cygwin, refer to Linux instructions instead.

Getting the iCub repository in Linux

icub-main

Run the following command in a console terminal, typically from the $code directory:

git clone https://github.com/robotology/icub-main.git

contrib software

Set up icub-contrib-common (see below), then get the contrib application that you wish to install (for example POETICON++), CMake and build it.

firmware (only for pc104)

git clone https://github.com/robotology/icub-firmware-shared
git clone https://github.com/robotology/icub-firmware-build

Compiling the iCub repository in Linux

icub-main

mkdir $ICUB_DIR
cd $ICUB_DIR
ccmake $ICUB_ROOT

In the CMake interface, set the following

CMAKE_BUILD_TYPE Release
ENABLE_icubmod_cartesiancontrollerclient ON
ENABLE_icubmod_cartesiancontrollerserver ON
ENABLE_icubmod_gazecontrollerclient ON

then hit c and g in order to generate the project files, to obtain the Makefile.

Having generated your project file, the actual compilation remains to be done:

make

Provided that YARP_ROBOT_NAME=iCubLisboa01 is set, robot-specific files will be automatically copied by CMake.

Don't use sudo make install! Rather, add the location of the binaries to the $PATH environment variable (see below).

icub-contrib-common metapackage (to use contrib modules, i.e., modules outside icub-main)

Follow the official instructions at the bottom of http://wiki.icub.org/wiki/Linux:Installation_from_sources but make sure to point CMAKE_INSTALL_PREFIX to the full path corresponding to $ICUBcontrib_DIR, which is accessible without administrator privileges and whose binaries will be within $PATH. To accomplish this, follow these simple instructions, paying attention to the part in bold.

Verify that your .bashrc_iCub file (or equivalent) contains these environment variables:

export ICUBcontrib_DIR=$code/icub-contrib-common/build
export PATH=$PATH:$YARP_DIR/bin:$ICUB_DIR/bin:$ICUBcontrib_DIR/bin
export YARP_DATA_DIRS=$YARP_DIR/share/yarp:$ICUB_DIR/share/iCub:$ICUBcontrib_DIR/share/ICUBcontrib

Set up the ICUBcontrib metapackage:

mkdir $ICUBcontrib_DIR
cd $ICUBcontrib_DIR
# the following command sets CMAKE_INSTALL_PREFIX to the path corresponding to $ICUBcontrib_DIR
# instead of /usr/local
cmake -DCMAKE_INSTALL_PREFIX=$(echo $ICUBcontrib_DIR) ..
ccmake ..
configure, generate, exit
make
make install

Don't use sudo make install! Rather, add the location of the binaries to the $PATH environment variable (see above).

At this point, you can install iCub Contrib applications with make install in their own build subdirectory (again, don't use sudo!). Binaries will be installed in $ICUBcontrib_DIR/bin. For example, to compile the POETICON++ build do the following:

cd $code/poeticon
mkdir build
cd build
cmake ..
configure, generate, exit
make
make install

Updating the iCub repository in Linux

cd $ICUB_ROOT
git pull

iCub Simulator

This component is optional. Refer to the official iCub manual, section 9 (Software), available at http://wiki.icub.org/wiki/Manual#Nine._Software.2C_iCub

See also

• http://wiki.icub.org/wiki/Manual#Six._Software.2C_Installing_YARP_and_iCub - official iCub manual
• iCub machines configuration
• http://wiki.icub.org/iCub/downloads/packages/windows/msvc8/