ICub instructions

From ISRWiki
Revision as of 15:56, 2 December 2015 by Giovanni Saponaro (talk | contribs) (→‎Hardware side: clean up information about transporting the iCub)
Jump to navigation Jump to search

This article explains how to use the full-body Lisbon iCub robot (codename: iCubLisboa01, nickname: Chico) for demos and experiments alike. We will describe the hardware setup that accompanies our iCub, how to turn things on and off, and how to run demos. For a generic description of the robot, refer to the Chico article.

An older version of this article can be found at iCub instructions/Archive.

Setup

The inventory consists of:

machine notes IP address, username
Chico the robot (duh) has a pc104 CPU in its head 10.10.1.50, icub
iCub laptop used to control the robot; also, it exports shared volumes (directories) to other machines 10.10.1.53, icub

Below Chico's support, from top to bottom we have:

what notes
Xantrex XFR 35-35 thin power supply unit, to power pc104 and some motors. Voltage: 12.9, current: 05.0 or more
Xantrex XFR 60-46 thick power supply unit, to power most motors. Voltage: 40.0 (initially it is 0 - it changes when you turn the green motor switch), current: 10.0 or more
APC UPS uninterruptible power supply

Switching on the robot

Hardware side

  • Check that the UPS is on
  • Check that the iCub laptop is on, if not switch it on
  • Turn on the Xantrex power supply units; make sure the voltage values are correct (see iCub_instructions#Setup)
  • Check that the red emergency button is unlocked
  • Turn on the green switches behind Chico
    • Safety hint: first turn on the pc104 CPU switch, wait for the CPU to be on, and only then switch the motors on
    • Another safety hint, after turning on motors: wait for the four purple lights on each board to turn off and become two blue lights – at this point you can continue to the next steps

Software side

  • Run cluster_manager.sh from the laptop desktop icon and start the needed YARP components (click here for detailed instructions). The summary is:
    • First, always launch yarpserver with the 'Run' button in the upper Nameserver panel
    • Then, if your application employs machines other than the laptop itself, launch the necessary yarprun listeners in the lower panel: icub-laptop, pc104, icubbrain1, icubbrain2, icub-cuda
  • Launch the yarpmanager.sh icon, which will open the manager GUI with all the necessary iCub applications
    • In the iCubStartup panel, launch all modules. Just in case, make sure that the iCub is vertical before launching this software, otherwise the robot will fall down (dangerous)
    • Other panels: depending on which demo you want to execute, you will need to start other necessary drivers such as cameras or facial expressions

Shutting off the robot

Software side

  • Stop your demo software and the cameras with the GUI; do not stop robotInterface (in the iCubStartup panel) nor yarpserver (in the Cluster Manager window) yet
  • In the iCubStartup panel of the GUI, stop all modules, including robotInterface. Chico will thus move its limbs and head to a "parking" position. (If things don't quit gracefully, stop or kill the process more times and be ready to hold Chico's chest since the head may fall to the front.)
  • In the Cluster Manager window, stop the instances of yarprun (lower panel). It is not necessary to stop yarpserver (upper panel), we usually keep it on

Hardware side

  • Shut down the pc104 with this command in a terminal: sudo halt
  • Turn off the two green switches. Pay attention when turning off the 'Motors' switch: if robotInterface was not stopped properly in the previous steps, then be ready to hold the robot when turning that switch
  • Turn off the Xantrex power supply units
  • Do not turn off the iCub laptop, we usually keep it on

Stopping the robot with the red emergency button

The emergency button, as the name suggests, is to be used for emergencies only. For example:

  • When the robot is about to break something
  • When some components make nasty noises that suggest they are going to break

Use this button with great care, as it cuts power to all motors and controllers abruptly! In particular, be ready to hold Chico, because the upper part of his body might fall upon losing power.

To start using the robot again, it is convenient to quit and restart all the software components and interfaces; refer to #Switching on the robot for that. Don't forget to unlock the red emergency button after an emergency, otherwise the program #robotInterface will start but not move any joint.

Starting YARP components

  • Click on the cluster_manager.sh icon on the desktop and select 'Run in Terminal' (or 'Run' if you want to suppress the optional debug information terminal)

  • You will see the following window, divided in two main components: yarpserver and yarpruns (the former is a global, single-instance nameserver; the latter are various instances of network command listeners, one per each machine involved in the demos)

  • In the yarpserver panel, click on the 'Run' button. The light above the 'Stop' button will become green.
  • In the yarprun panel, choose all the machines in the 'Select' column (icub-laptop, pc104, icubbrain1, icubbrain2, icub-cuda, etc.), then click 'Run Selected' and wait a bit so that all machines can turn on their green 'On' light.

Other components

Many demos and programs assume that components such as cameras, the robotInterface driver or the facial expression driver have been launched. To start them, first of all run the yarpmanager.sh icon. A GUI similar to this one will appear:

When you have one or more applications running, each one will have its panel (tab) and the following toolbar will be visible. Here are the most important functions (which affect all modules of the currently selected application):

robotInterface

This program controls the motors and reads the robot sensors (encoders, inertial sensor, skin, force/torque). It is needed by almost all demos.

  • check that the red emergency button is unlocked
  • open the iCubStartup panel in the yarpmanager GUI; click the Run Application button. This will start both kinematics (robotInterface, cartesian solvers and gaze control) and dynamics (wholeBodyDynamics and gravityCompensator)

Wait for all boards to answer (which takes around 1 minute); after that, you are ready to move on.

There is a GUI application to manually command robot joints. Just invoke it from the iCub laptop with: 

yarpmotorgui

Cameras

Facial expression driver

Note that the actual expression device driver (the first module of the two listed) runs on the pc104. Sometimes, that process cannot be properly killed and restarted from the graphical interface; in the event of you needing to do that, you can either kill -9 its PID, or do a hard restart of the pc104.

iCubGui

This (optional) component shows a real-time 3D model of the robot on the screen.

Skin GUI

Specific demos

Refer to iCub demos/Archive for older information such as starting demos from terminals.

Ball tracking and grasping

  • Make sure that basic YARP components are running: summarized Cluster Manager instructions are here; detailed instructions are in section #Starting YARP components
  • Make sure that the applications iCubStartup, Cameras_320x240_for_Ball_Tracking have been started
  • Optionally, Face_Expression and iCubGui can be started too
  • open the Red-Ball_Demo panel in the yarpmanager GUI; click the Run Application button; click the Connect Links button

Note that this demo launches the left eye camera with special parameter values: 

 brightness 0
 sharpness 0.5
 white balance red 0.474      // you may need to lower this, depending on illumination
 white balance blue 0.648 
 hue 0.482
 saturation 0.826
 gamma 0.400
 shutter 0.592
 gain 0.305

Face tracking

Facial expressions

Force Control

  • Make sure that basic YARP components are running: summarized Cluster Manager instructions are here; detailed instructions are in section #Starting YARP components
  • Make sure that the applications iCubStartup has been started
  • Click on the Force_Control panel in the yarpmanager GUI, Run Application, Connect Links
  • select the desired modality (screenshot below) and manually move the robot limbs:

Interactive Objects Learning Behavior

For this demo, you also need a Windows machine with a yarprun listener (the speech recognition module will be launched on this machine).

In yarpmanager, select the "Interactive Objects Learning Behavior with SCSPM" application: refresh, run, connect.

The grammar of recognized spoken sentences is located at https://github.com/robotology/iol/blob/master/app/lua/verbalInteraction.txt

Notes: do the following commands for using IOL Object Recognition side by side with the POETICON++ demo. 

 yarp rpc /actionsRenderingEngine/cmd:io
 home all

 yarp rpc /iolStateMachineHandler/human:rpc
 attention stop

Yoga

Retrieved from "http://mediawiki.isr.tecnico.ulisboa.pt/index.php?title=ICub_instructions&oldid=6464"